P60-SE Special Edition   

 

  

   

JetCat P60-SE SPecial Edition Turbine complete with starter includes:

  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual  

 

 

Thrust:

13 LB @ 165,000 RPM

Weight:

1.87 LB, incl. starter

Diameter:

3.25 inches

RPM Range:

50,000 - 165,000

Exhaust gas temp.:

580°C -690°C

Fuel consumption:

8 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours

  JetCat P-70   

  

JetCat P-70 turbine complete with starter includes:  

  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual

  

Thrust:

17.5 LB @ 123,000 RPM

Weight:

2.6 LB, incl. starter

Diameter:

3.7 inches

RPM Range:

35,000 - 123,000

Exhaust gas temp.:

620°C

Fuel consumption:

8 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours

JetCat P-80-SE   

 

  

 

Introducing the new JetCat P80-SE with more POWER and enhanced reliability.

The P80-SE continues our extreemly successfull P80 engine. The new design of the P80-SE incorporates an optimized compressor/diffusor-system, resulting in higher engine performance and reliability.

The engine follows throttle commands almost without delay. In addition to the outstanding features of or ECU V6.0, the new ECU V6.3 has an „auto power down“ function built in, which allows to switch off the engine power supply (--> receiver off) before the engine cool down sequence has been finished. In this case the ECU will stay powered on, finish the cool down sequence and then auto power down itself. 

        

 

JetCat P-80-SE turbine complete with starter includes:  

  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual 

 

Thrust:

22 LB @ 125,000 RPM

Weight:

2.9 LB, incl. starter

Diameter:

4.4 inches

RPM Range:

35,000 - 125,000

Exhaust gas temp.:

580°C -690°C

Fuel consumption:

9 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours  

 

 

 P120 Special eXtreme Edition   

  

 

JetCat P-120-SX turbine complete with starter includes:

  • Jet-tronic ECU (fuel control electronics)
  • CAD designed and machined from billet compressor wheel
  • Internal kerosene starting plug for single fuel operation. Fast startup!
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual

 

Thrust:

Thrust is 30 lbs @ 125,000 RPM

Weight:

3.1 LB

Diameter:

4.4 inches

RPM Range:

33,000 - 125,000 RPM

Exhaust gas temp.:

580°C-690°C

Fuel consumption:

12oz/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours

JetCat P160-SX   

 

 

 

JetCat P160-SX turbine complete with starter includes : 

  •   6 lbs more thrust than the P120-SX
  • CAD designed and machined from billet compressor wheel
  • Internal kerosene starting plug for single fuel operation. Fast startup!
  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual

 

Thrust:

36 lbs @ 125,000 RPM

Weight:

3.1 LB

Diameter:

4.4 inches

RPM Range:

32,000 - 125,000 RPM

Exhaust gas temp.:

650°C-750°C

Fuel consumption:

17 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours

JetCat P-180    

 

 

 

JetCat P-180 turbine comes complete with HEAVY DUTY starter and includes:

  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 3800mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual

 

Thrust:

45 lbs @ 110,000 RPM

Weight:

5 LB

Diameter:

4.72 inches

RPM Range:

32,000 - 110,000 RPM

Exhaust gas temp.:

580°C-720°C

Fuel consumption:

24 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours

JetCat P-200    

 

   

 

JetCat P-200 turbine comes complete with HEAVY DUTY starter and includes: 

 

· Jet-tronic ECU (fuel control electronics)
· GSU (Display and Programmer)
· LED I/O board · Miniature fuel pump
· Electronic starting gas valve
· Electronic Fuel valve
· Fuel tubing, tubing connector set, filters, and cable set
·2 cell, 3800mA LiPoly battery pack
· Starting gas tank
· Turbine mounting clamp
· Detailed instruction manual  

  

 

 

Thrust:

52 lbs @ 112,000 RPM

Weight:

5 LB

Diameter:

5.12 inches

RPM Range:

32,000 - 112,000 RPM

Exhaust gas temp.:

580°C-690°C

Fuel consumption:

24 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic Oil in the fuel

Maintenance interval:

25 hours

JetCat HP5 

   

·  Real turbine power with tremendous reserve, capable of powering even the largest helicopters

·  Rotor direction selectable for either (CW/CCW) rotation

·  Rotor decoupled from turbine via centrifugal clutch allowing the rotor to stop when the turbine is at idle

·  Optional servo driven rotor brake

 

  

Original JetCat AutoStart system: 

·        Original JetCat AutoStart system:
Fully automatic turbine startup by a command from the R/C transmitter, without external connections

·        Low maintenance, quiet running tooth belt drive
in the primary gear stages

·        Special shaped gear mechanism in the final gear stage for silent operation and positive power transmission

·        Complete package: unpack, install, fly!

·        Over 1000 customers have proven the reliability
of this turbine engine power plant.

·        Precision ceramic ball bearings for low maintenance operation.

·        Screen in front of the turbine inlet avoids FOD
(foreign object damage) of the compressor / turbine

·        Special CAD designed turbine wheel, for maximum shaft power at minimum residual thrust

·        Original JetCat “Jet-tronic” ECU: RPM regulator for constant rotor speed. User programmable electronics.

·        Turbine starts without compressed air or fans. Automatic cooling when the turbine is shut off.

·        RS232 serial interface for linking to a computer

·        Plain text display of the current running parameters for example: exhaust gas temperature, RPM, fuel consumption,
remaining fuel, last run time, total run time, battery voltage,
turbine condition, last shut-down reason, etc. 

 

JetCat SPT5   

  

JetCat SPT5 turbo-prop complete with starter includes: 

 

   

·        Jet-tronic ECU (fuel control electronics)

·        GSU (Display and Programmer)

·        LED I/O board

·        Miniature fuel pump

·        Electronic starting gas valve

·        Electronic Fuel valve

·        Fuel tubing, tubing connector set, filters, and cable set

·        2 cell, 3800mA LiPoly battery pack

·        Starting gas tank

·        Turbine mounting clamp and front mounting flange included

·        Both shafts are electronically monitored and controlled

·        Drive exhibits very low vibrations

·        Compact, high efficiency planetary drive system

·        Low maintenance lubrication system Integrated cooling fan propeller

·        Detailed instruction manual

  

 

Thrust:

55 lbs with 27" prop at 7,0000 RPM

Weight:

4.9 LB, incl. starter

Length:

15.25 inches

Turbine RPM Range:

50,000 - 165,000

Propeller RPM Range:

1500 - 7000 RPM

Exhaust gas temp.:

580°C -710°C

Fuel consumption:

8 oz per/min at full power

Fuel:

Jet A1, 1-K kerosene

Lubrication:

approximately 5% synthetic turbine oil in the fuel

Maintenance interval:

50 hours